How To Cut The Pvc Skirting Board

How to properly trim the corners of the skirting board

Since it is hard plastic skirting boards that are increasingly used during repairs, it is about them that will be discussed. Their installation is inevitably associated with the need to cut and form beautiful joints in the corners. The quality of all work and the appearance of the room where the repair is being made will depend on how the plinth will be joined, in general. How to cut off a plastic skirting board: how to cut and how to cut it correctly, cutting methods

A skirting board is an essential element for decorating a room and giving it a complete and neat look. It can be made of various materials, but plastic skirting boards are especially popular now. It is easy to install, but even in this process there are some subtleties that are important to know about. How to cut a plastic skirting board correctly so that you can neatly dock it in the corners?

How to cut a plastic skirting boardThe main types of floor skirting boards

The wooden skirting board is a classic. It is a natural product, as it is made from solid wood. This type is distinguished by high strength and durability. the skirting boards, installed back in the times of the USSR, still serve faithfully in some apartments and houses. Now they are made mainly of pine wood, but there are also products from walnut, oak, ash and other species. However, due to this, the cost of products increases. not everyone can afford such skirting boards.

Because of this, veneered skirting boards have appeared on the market. their are an order of magnitude lower. However, outwardly, they practically do not differ from products made of expensive wood. The fact is that their upper part, which plays a decorative role, is just made of a thin layer of expensive wood. Without certain knowledge and experience, it is almost impossible to distinguish veneered skirting from ordinary wood.

It is convenient to cut wooden skirting boards with a hacksaw for metal

The most popular now is the plastic skirting board, that is, made of PVC. It has partially displaced conventional wood products from the market, as it has a number of advantages:Looks nice and neat. it is able to imitate products made from natural wood; Easy to install, flexible and very easy to cut; Can serve as a cable channel for wiring; Not afraid of exposure to water, and also does not rot, mold does not start on it; Inexpensive compared to wood or veneer.

Plastic skirting board is made of polyvinyl chloride, which is passed through special forms under high pressure. After the mass has solidified, a neat plastic product is obtained.

Plastic skirting boards are of several types. for example, used for carpet (they have a special shape in the form of the letter G, fix the material) or for linoleum. There are also universal products that can be installed on any type of flooring. They can be classified and depending on the hardness.

Table. Types of plastic skirting boards depending on hardness.

Flexible plastic skirting boardsCutting the skirting board with a miter box

For the correct trimming of the plinth, a special device was invented, which was called the miter box. It is a small block with a notch for the skirting board and with gaps located at different angles. for the cutting tool.

With a miter box, you can get neat and even cuts. The plinth is fixed inside the product, then the angle and direction of cut required in a particular case are selected.

We make a miter box with our own hands

When working with a miter box, it is important to ensure that the edges of the skirting board protrude a short distance beyond the edges of the selected slot. If the trimming tool is wider than the skirting board itself, it is recommended to securely fix the product inside the miter box before trimming. Otherwise, the plinth can move inside, the cut angle will constantly change, because of which it (cut) will turn out to be incorrect and incorrect.

Making cuts for joining skirting boards using a miter box

Cutting with a rotary miterUseful Tips

Experienced craftsmen recommend starting the installation of the skirting board from the inner corner. At the junction of the two walls, which form the inner corner, the cut on the baseboards will be 45 degrees (in a room with correct and accurate geometry). It is recommended to cut with a miter box. this is the only way to achieve a perfectly even cut.

Cutting floor and ceiling plinths with a miter box

In general, in any case, the cut edges of plastic skirting boards should be sanded. this way it will be possible to get rid of sharp edges, and it will be easier to work. And the skirting boards with cable channels are cut only after the product has been disassembled. the decorative strip designed to hide the wires and attachment points of the skirting board is cut separately.

The plinth is cut to the desired size

It is recommended that immediately before installing the plinth, cut the pieces to the required length and arrange the corners so as not to be distracted by this procedure during the assembly of the plinth. You should not neglect the use of additional elements. plugs, corners and other products for the baseboard. With their help, it will be possible to give the finished work a complete and harmonious look.

It is very easy to cut skirting boards at any angle with this device. Methods for cutting plastic skirting boards

Cutting the skirting board is seemingly simple, but responsible. If the corners are cut incorrectly, then they will not fit correctly and all the work will go down the drain, since the product will no longer have a beautiful appearance. there will be gaps between two sections of the plinth and decorative inserts (corners, connecting elements, etc.).

Most often, an ordinary metal hacksaw, which has fine teeth, is used to cut the plinth. However, it will not work for thin skirting boards, since the product will simply tear under the influence of this tool.

Plastic skirting board cutting angle grinder

Sometimes the plinth is cut with metal scissors. But the method also has its drawbacks, because the product can be crumpled under the pressure of the blades. Less commonly, but still used is an angle grinder. However, the line cut after it can be sloppy, as the tool often "tears" soft plastic. Especially often this method turns out to be unsuccessful for beginners in the world of repair, who still do not know how to fully control the work. So the angle grinder can be attributed to rather specific methods.

The most important thing in the procedure for cutting skirting boards is observing the required geometry. The procedure is never performed "by eye", here the accuracy of measurements and accuracy are important. Therefore, there are other methods for cutting skirting boards.

The absence of fittings suggests the use of other methods of connecting skirting boards. This is an option with and without clipping templates. Using a ruler and pencil without a miter box

Sometimes precise work has to be done with primitive tools. It is possible to very accurately mark the cutting line on the ceiling plinth, using only a pencil and a ruler.

The operation is performed in four steps:Attach the skirting board to the ceiling and rest its end against the opposite wall. Draw a line with a pencil along the edge of the plinth on the ceiling. Repeat this action along another wall. Pencil mowing lines on the ceiling will intersect and form a cross. A line is drawn along the ruler, connecting the marked cross with the joining point of the walls and ceiling. This line is the trimming line for the skirting board. How to file an outer corner

When filing the outer corner, the chamfers at the abutting ends of the skirting board are sawn at an angle of 45 ° and must look inward. Methods for cutting plastic skirting boards

Cutting plastic and foam skirting boards is no problem. The main task is to apply the cut line correctly. This is done differently for the inside and outside corners. Varieties of plastic skirting boards

Plastic skirting boards have replaced the wooden ones used in previous years. They have a number of advantages. They are made from polyvinyl chloride (PVC), a material that is widely used in industry and construction. Outwardly, they imitate any wood species. Easy to process, easy to install. They are immune to mold, mildew, dampness, easy to clean. They are much cheaper than wooden.

Plastic skirting boards come in different shapes and colors. Skirting boards from different manufacturers differ among themselves. For each specific product, you need to apply the appropriate processing technology.

There are types of plastic skirting boards focused on a specific floor covering. carpet, linoleum or parquet.